Job Description
Jr. Engineer
LNT/-E/1314013
LTPO-L&T Energy-CarbonLite SolutionsHazira Mfg Complex
Posted On
17 Apr 2026
End Date
14 Oct 2026
Required Experience
4 - 6 Years
Skills
Knowledge & Posting Location
ELECTRIC POWER
OFFICE 365
OPERATION
MAINTENANCE
Minimum Qualification
GENERAL DIPLOMA
Job Description
1.Should have knowledge of maintenance, trouble shooting & operation of auxiliaries for generator (upto 1000 MW) like single & double flow seal oil system, stator coil cooling water, lubrication oil system, jacking oil system, H2 & CO2 handling.
2.Should have knowledge of electrical testing on stator & rotor manufacturing :
a.Generator stator:
i.Insulation resistance measurement
ii.DC winding resistance
iii.Tan delta & capacitance measurement
iv.Partial discharge measurement
v.NFT of overhang winding
vi.Core loop flux test
vii.ELCID
b.Generator rotor :
i.Insulation resistance measurement
ii.DC winding resistance
iii.Impedance measurement
iv.RSO
3.Should have knowledge of generator routine & type test during dynamic condition:
a.Temperature rise – heat run
b.Open circuit test
c.Short circuit test
d.Sudden short circuit test
e.Negative sequence & Positive sequence test
f.THF & Voltage waveform deviation
4.Should have knowledge of IEC, ISO standards for electrical testing of generator ( up to 1000 MW) & High-speed balancing of turbine / generator rotors
5.Should have knowledge of Low speed & high-speed balancing of turbine & generator rotors
6.Should have knowledge of assembly of rotors in high-speed balancing tunnel
a.Able to visually check rotor
b.Able to take TOP / Side clearance of bearing & rotor journal
c.Able to perform alignment of rotor with motor shaft
d.Able to trouble shoot issues pertaining in assembly process
7.Can study P&ID, electrical drawings for maintenance & operation parameters
8.Have a positive approach for trouble shooting of electrical, mechanical & instrumentation issues in generator testing, high speed balancing &
+.Able to handle unionized workmen in shift, ready to work in shifts
10.Additional Vibration category – 2 certification is preferable
11.Able to handle customer at site for overhauling activities like in-situ balancing, electrical test on generator stator & rotor, calibration of instruments & operation/maintenance of auxiliaries, ready to travel at different sites
12.Should have knowledge of basic instrumentations/transducers like pressure transmitter, pressure gauge, RTD, Thermocouple etc.
13.Able to operate electrical testing kits like
a.Insulation tester
b.High voltage test set-up
c.Micro-ohm meter
d.PD kit
e.Tan- delta kit
f.Function generator
g.1- phase varaic
LNT/-E/1314013
LTPO-L&T Energy-CarbonLite SolutionsHazira Mfg Complex
Posted On
17 Apr 2026
End Date
14 Oct 2026
Required Experience
4 - 6 Years
Skills
Knowledge & Posting Location
ELECTRIC POWER
OFFICE 365
OPERATION
MAINTENANCE
Minimum Qualification
GENERAL DIPLOMA
Job Description
1.Should have knowledge of maintenance, trouble shooting & operation of auxiliaries for generator (upto 1000 MW) like single & double flow seal oil system, stator coil cooling water, lubrication oil system, jacking oil system, H2 & CO2 handling.
2.Should have knowledge of electrical testing on stator & rotor manufacturing :
a.Generator stator:
i.Insulation resistance measurement
ii.DC winding resistance
iii.Tan delta & capacitance measurement
iv.Partial discharge measurement
v.NFT of overhang winding
vi.Core loop flux test
vii.ELCID
b.Generator rotor :
i.Insulation resistance measurement
ii.DC winding resistance
iii.Impedance measurement
iv.RSO
3.Should have knowledge of generator routine & type test during dynamic condition:
a.Temperature rise – heat run
b.Open circuit test
c.Short circuit test
d.Sudden short circuit test
e.Negative sequence & Positive sequence test
f.THF & Voltage waveform deviation
4.Should have knowledge of IEC, ISO standards for electrical testing of generator ( up to 1000 MW) & High-speed balancing of turbine / generator rotors
5.Should have knowledge of Low speed & high-speed balancing of turbine & generator rotors
6.Should have knowledge of assembly of rotors in high-speed balancing tunnel
a.Able to visually check rotor
b.Able to take TOP / Side clearance of bearing & rotor journal
c.Able to perform alignment of rotor with motor shaft
d.Able to trouble shoot issues pertaining in assembly process
7.Can study P&ID, electrical drawings for maintenance & operation parameters
8.Have a positive approach for trouble shooting of electrical, mechanical & instrumentation issues in generator testing, high speed balancing &
+.Able to handle unionized workmen in shift, ready to work in shifts
10.Additional Vibration category – 2 certification is preferable
11.Able to handle customer at site for overhauling activities like in-situ balancing, electrical test on generator stator & rotor, calibration of instruments & operation/maintenance of auxiliaries, ready to travel at different sites
12.Should have knowledge of basic instrumentations/transducers like pressure transmitter, pressure gauge, RTD, Thermocouple etc.
13.Able to operate electrical testing kits like
a.Insulation tester
b.High voltage test set-up
c.Micro-ohm meter
d.PD kit
e.Tan- delta kit
f.Function generator
g.1- phase varaic
💡 Quick Summary
Seeking a career-building opportunity? The Jr. Engineer position is now open for candidates interested in the IT Engineer & Developer Jobs sector. This role in Hajira offers a professional environment and growth potential.
Requirement Snapshot: Candidates should possess basic communication skills, a proactive attitude, and the ability to work in a team. Experience in IT Engineer & Developer Jobs is a plus.
